On-Site Workshop: 2-Day Hazardous Area Australian Standards Simplified (Groups II & III) 2018

This workshop provides an introduction to electrical compliance and your responsibilities in Group II (flammable gases, liquids and vapours) and Group III (combustible dusts) hazardous areas.

Potential sources of ignition are often taken into hazardous locations where flammable liquids, gases, vapours and dusts are generated, processed, handled and stored. These flammable substances can easily ignite from an arc, spark or heat. It is essential you avoid accidental ignition of these flammable substances.

This workshop is suitable as first time, refresher and continuing training for engineers,
consultants, supervisors, buyers and suppliers requiring an introduction to electrical installations in hazardous areas.

Trainees will receive a basic understanding of hazardous area legislation, how hazardous areas are classified, sources of ignition and the basic electrical requirements for hazardous areas based on current Australian Standards.

Ensure you remain compliant* and maintain your hazardous area skills and knowledge by booking this essential workshop today.

Who is Explosion Protection Technology Pty Ltd?
Explosion Protection Technology Pty Ltd specialises in hazardous area training, hazardous area classifications, hazardous area inspections and audits of facilities and assets Australia wide. We are practising professional hazardous area trainers and consulting engineers.

Upon completion of this workshop trainees should:

  • Understand how to prevent hazardous area fires and explosions
  • Be up-to-date with changes in the relevant hazardous area Australian Standards
  • Understand legislation, compliance and competency
  • Have existing hazardous area knowledge reinforced
  • Know the basics of how Group II and Group III hazardous areas are classified
  • Understand hazardous area classification drawings
  • Understand equipment markings
  • Understand sources of ignition
  • Know the basics of how:
      • Flameproof, Increased Safety, Dust Tight and Intrinsic Safety are used to make electrical equipment safe for use in hazardous areas
      • To use the relevant Australian Standards to select, install, inspect and maintain Flameproof, Increased Safety, Dust Tight and Intrinsically Safe electrical equipment and wiring
      • Hazardous area electrical equipment certified to other Standards is selected and assessed to ensure it offers the equivalent level of safety to the relevant Australian Standard

Workshop outline:

1.  Introduction

  • Hazardous areas
  • Who is responsible
  • Statute laws and standards
  • AS/NZS3000 non compliance issues
  • Qualifications and competency

2.  Hazardous Area Classification

  • Zone classification - Group II
  • Gas classification - equipment group
  • Temperature classification - T Class
  • Ambient temperature range of explosion protected equipment
  • Area classification - Group II
  • Combustible dusts - Group III

3.  Sources of Ignition

4.  Types of Protection

  • Ex d - Flameproof
  • Ex e - Increased Safety
  • Ex tD and DIP - Dust Tight
  • Ex i and Ex iD - Intrinsic Safety

5. Equipotential Bonding

6. Selection of Equipment

  • List of Australian Standards
  • AUS Ex, ANZEx and IECEx certified equipment
  • Permitted electrical equipment
  • Other standards certified equipment

7.  Certification

  • Certification of electrical equipment
  • Simple apparatus
  • Energy storing Ex i equipment

8.  Theory of Intrinsic Safety

  • Zener diodes
  • Zener barrier
  • “Ex ia”, “Ex ib” and “Ex ic” Zener barriers
  • Earthing
  • Isolation barrier theory

9. Installation of

  • Ex d - Flameproof
  • Ex e - Increased Safety
  • Ex tD and DIP - Dust Tight
  • Ex i and Ex iD - Intrinsic Safety

10.  Inspection

  • Inspection schedules

11.  Maintenance and Repair

12.  Summary

13.  Self Appraisal

  • Appraisal questionnaire
  • Appraisal questionnaire answers

14. Discussion

Date of Workshop: Date to be agreed
Time: 7.00-7.30 am registration
7.30 am to 4.30 pm workshop (To be agreed)
Breaks : 8.30-8.35 am              Brain recovery
9.30 —9.45 am            Tea/coffee
11.00 —11.05 am         Brain recovery
12 noon —12.40 pm      Lunch
1.40 —1.45 pm            Brain recovery
2.45 —3.00 pm            Tea/coffee
Venue: At your factory
Catering: You provide all tea, coffee, soft drinks and light lunches
CPD: This workshop provides 18 hours of Continuous Professional Development (CPD) to assist practicing professional engineers and technicians to maintain and develop their hazardous area technical skills and knowledge.
Full Workshop Fee: Workshops presented from 1st January to 31st December 2018
$670.00 + $67.00 (GST) = $737.00 per person
Minimum number of trainees is 10 and maximum is 25.
Workshop fee includes:
  • Comprehensive workshop notes
  • Workshop certificate
Early Bird Discount: Save an amazing $110.00 per person by paying within 14 days after the start of the workshop
Early bird fee: $570.00 + $57.00 (GST) = $627.00 per person
Payment: Full workshop fee: Payment must be received within 28 days after commencement of workshop.
Early bird discount: Payment must be received within 14 days after commencement of workshop to receive discounted fee.
MasterCard, Visa, cheque or EFT are accepted.
Substitutes: If an enrolled person is unable to attend a substitute is allowed at no extra charge. Details must be faxed or emailed in advance.
Transfers: Enrolment transfers to another workshop are not permitted.
Cancellations: A $82.50 fee applies to each cancelled workshop place received in writing more than two weeks prior to the agreed commencement date of the workshop. Regrettably, no refunds are available after this date or if a trainee fails to attend and no substitute fills the place. The workshop folder will be posted to the enrolled trainee. A letter will be mailed following payment in full advising a 40% discount applies on one future 2-day workshop place for each cancelled or no show booking. This offer is valid for 12 months and no further discounts will apply.
Set-up: Venue needs to be set-up the afternoon prior to commencement of workshop. Seating should be at tables arranged in a U shape with six additional large tables for demonstration equipment and documentation. Click HERE to see suggested room layout. Note Boardroom tables are unsuitable.
Names: A list of all enrolled trainees names is required two weeks prior to commencement of the workshop. Please provide the following for each trainee:
  • Trainee name for name badge and workshop folder
  • Name (if different to name badge) for certificate
  • Job title
  • Contact phone number, fax and or email address

Delivery of workshop:

Workshops are presented using PowerPoint slides, a video clips, video tapes and real hazardous area electrical equipment.

Workshop Presenter

Colin Baker is a practising professional engineer, qualified workplace assessor (Certificate IV) and workplace trainer who has been involved with surge protection, intrinsic safety and hazardous area installations since 1970.  He has worked for some of the major manufacturers of hazardous area instrumentation and has gained significant surge protection and hazardous area experience through designing, installing, commissioning and inspecting equipment and installations.

Colin has provided training and technical support to many chemical, petrochemical and public utility companies around the world and has written and presented numerous papers locally and internationally.

An H Class Licensed Electrical Inspector (Vic) and an Accredited Auditor (Qld), Colin is qualified to inspect hazardous area electrical installations under the 2009 Victoria Electricity Safety (Installation) Regulations and the 2002 Queensland Electrical Safety Regulation.

He sits on the joint Australian/New Zealand Standards committees MS-066 (was P-012) for hazardous area competency, EL-014 for equipment in explosive atmospheres and MS-011 for classification of hazardous areas. He sits on sub-committees EL-014-4 for standards on Intrinsic Safety, Encapsulation, Special Protection and Combustible Dusts; ME-026-02 for standards on industrial hazardous area trucks; EL-014-8 for standards on spray painting booths and has provided input for EL-014-9 for standards on gas detectors.

Explosion Protection Technology Pty Ltd is a leading independent and Australian owned consulting and training organisations founded by Colin.  The company specialising in the safety of hazardous area electrical installations based on the current Australian Standards including:

  • Classifying hazardous areas
  • Checking electrical installations located in hazardous areas
  • Assisting clients to obtain certification of hazardous area electrical equipment
  • Running hazardous area workshops


Education or Training *Continuing education or training is required - see clause 4.5 of AS/NZS600079.14:2017 and clause 4.2 of AS/NZS600079.17:2017




Call Today

(03) 9707 3110

1-Day Basic
Sydney (Casula)
4 Sept 2018
Sydney (Parramatta)
11 Sept 2018
2-Day Simplified
Melbourne (Highett)
17 - 18 July 2018
Melbourne (Taylors Lakes)
31 July - 1 Aug 2018
3-Day Comprehensive
Melbourne (Highett)
9 - 11 Oct 2018
Melbourne (Taylors Lakes)
16 - 18 Oct 2018
Sydney (Casula)
27 - 29 Nov 2018
Sydney (Parramatta)
4 - 6 Dec 2018
1-Day Basics
1-Day Group II
1-Day Group III
1-Day Groups II and III
2-Day Simplfied
2-Day Group II
2-Day Groups II and III
3-Day Comprehensive
3-Day Group II
3-Day Group III
3-Day Groups II and III
Copyright © 2018 Explosion Protection Technology Pty Ltd Privacy Policy